主播的第一个文章全部免费因为我很多程序也是参考其他道友开源的。
本博客不啰嗦，不讲原理只讲跑通
单片机STM32全部适配
HAL库
oled模块IIC的
/****************下面开始咱们的教学*****************/
先说注意事项 第一软件模拟IIC 第二oled 3.3V供电 其他没了就这么点 别接错线千万
第一步 打开Cubemx 选择好你的单片机型号 配置时钟树之类的主播不在赘述，这是主播的一个小实验工程有一些别的引脚配置不需要搭理
第二步生成程序 自动跳转到Keil5下面是重点你将看到绝对干货
第三步不管三七二十一把图片下面附加的程序给主播放到gpio.c里或者是直接放在main.c（为什么这样做呢？我只说一次照顾最小最小的小白不知道头文件和变量全局声明的“最大的小白”）
/*引脚配置*/ #define OLED_W_SCL(x) HAL_GPIO_WritePin(GPIOA, GPIO_PIN_9, (GPIO_PinState)(x)) #define OLED_W_SDA(x) HAL_GPIO_WritePin(GPIOA, GPIO_PIN_8, (GPIO_PinState)(x)) /*引脚初始化*/ void OLED_I2C_Init(void) { OLED_W_SCL(1); OLED_W_SDA(1); } /** * @brief I2C开始 * @param 无 * @retval 无 */ void OLED_I2C_Start(void) { OLED_W_SDA(1); OLED_W_SCL(1); OLED_W_SDA(0); OLED_W_SCL(0); } /** * @brief I2C停止 * @param 无 * @retval 无 */ void OLED_I2C_Stop(void) { OLED_W_SDA(0); OLED_W_SCL(1); OLED_W_SDA(1); } /** * @brief I2C发送一个字节 * @param Byte 要发送的一个字节 * @retval 无 */ void OLED_I2C_SendByte(uint8_t Byte) { uint8_t i; for (i = 0; i < 8; i++) { OLED_W_SDA(Byte & (0x80 >> i)); OLED_W_SCL(1); OLED_W_SCL(0); } OLED_W_SCL(1); //额外的一个时钟，不处理应答信号 OLED_W_SCL(0); } /** * @brief OLED写命令 * @param Command 要写入的命令 * @retval 无 */ void OLED_WriteCommand(uint8_t Command) { OLED_I2C_Start(); OLED_I2C_SendByte(0x78); //从机地址 OLED_I2C_SendByte(0x00); //写命令 OLED_I2C_SendByte(Command); OLED_I2C_Stop(); } /** * @brief OLED写数据 * @param Data 要写入的数据 * @retval 无 */ void OLED_WriteData(uint8_t Data) { OLED_I2C_Start(); OLED_I2C_SendByte(0x78); //从机地址 OLED_I2C_SendByte(0x40); //写数据 OLED_I2C_SendByte(Data); OLED_I2C_Stop(); } /** * @brief OLED设置光标位置 * @param Y 以左上角为原点，向下方向的坐标，范围：0~7 * @param X 以左上角为原点，向右方向的坐标，范围：0~127 * @retval 无 */ void OLED_SetCursor(uint8_t Y, uint8_t X) { OLED_WriteCommand(0xB0 | Y); //设置Y位置 OLED_WriteCommand(0x10 | ((X & 0xF0) >> 4)); //设置X位置高4位 OLED_WriteCommand(0x00 | (X & 0x0F)); //设置X位置低4位 } /** * @brief OLED清屏 * @param 无 * @retval 无 */ void OLED_Clear(void) { uint8_t i, j; for (j = 0; j < 8; j++) { OLED_SetCursor(j, 0); for(i = 0; i < 128; i++) { OLED_WriteData(0x00); } } } /** * @brief OLED显示一个字符 * @param Line 行位置，范围：1~4 * @param Column 列位置，范围：1~16 * @param Char 要显示的一个字符，范围：ASCII可见字符 * @retval 无 */ void OLED_ShowChar(uint8_t Line, uint8_t Column, char Char) { uint8_t i; OLED_SetCursor((Line - 1) * 2, (Column - 1) * 8); //设置光标位置在上半部分 for (i = 0; i < 8; i++) { OLED_WriteData(OLED_F8x16[Char - ' '][i]); //显示上半部分内容 } OLED_SetCursor((Line - 1) * 2 + 1, (Column - 1) * 8); //设置光标位置在下半部分 for (i = 0; i < 8; i++) { OLED_WriteData(OLED_F8x16[Char - ' '][i + 8]); //显示下半部分内容 } } /** * @brief OLED显示字符串 * @param Line 起始行位置，范围：1~4 * @param Column 起始列位置，范围：1~16 * @param String 要显示的字符串，范围：ASCII可见字符 * @retval 无 */ void OLED_ShowString(uint8_t Line, uint8_t Column, char *String) { uint8_t i; for (i = 0; String[i] != '\0'; i++) { OLED_ShowChar(Line, Column + i, String[i]); } } /** * @brief OLED次方函数 * @retval 返回值等于X的Y次方 */ uint32_t OLED_Pow(uint32_t X, uint32_t Y) { uint32_t Result = 1; while (Y--) { Result *= X; } return Result; } /** * @brief OLED显示数字（十进制，正数） * @param Line 起始行位置，范围：1~4 * @param Column 起始列位置，范围：1~16 * @param Number 要显示的数字，范围：0~4294967295 * @param Length 要显示数字的长度，范围：1~10 * @retval 无 */ void OLED_ShowNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length) { uint8_t i; for (i = 0; i < Length; i++) { OLED_ShowChar(Line, Column + i, Number / OLED_Pow(10, Length - i - 1) % 10 + '0'); } } /** * @brief OLED显示数字（十进制，带符号数） * @param Line 起始行位置，范围：1~4 * @param Column 起始列位置，范围：1~16 * @param Number 要显示的数字，范围：-2147483648~2147483647 * @param Length 要显示数字的长度，范围：1~10 * @retval 无 */ void OLED_ShowSignedNum(uint8_t Line, uint8_t Column, int32_t Number, uint8_t Length) { uint8_t i; uint32_t Number1; if (Number >= 0) { OLED_ShowChar(Line, Column, '+'); Number1 = Number; } else { OLED_ShowChar(Line, Column, '-'); Number1 = -Number; } for (i = 0; i < Length; i++) { OLED_ShowChar(Line, Column + i + 1, Number1 / OLED_Pow(10, Length - i - 1) % 10 + '0'); } } /** * @brief OLED显示数字（十六进制，正数） * @param Line 起始行位置，范围：1~4 * @param Column 起始列位置，范围：1~16 * @param Number 要显示的数字，范围：0~0xFFFFFFFF * @param Length 要显示数字的长度，范围：1~8 * @retval 无 */ void OLED_ShowHexNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length) { uint8_t i, SingleNumber; for (i = 0; i < Length; i++) { SingleNumber = Number / OLED_Pow(16, Length - i - 1) % 16; if (SingleNumber < 10) { OLED_ShowChar(Line, Column + i, SingleNumber + '0'); } else { OLED_ShowChar(Line, Column + i, SingleNumber - 10 + 'A'); } } } /** * @brief OLED显示数字（二进制，正数） * @param Line 起始行位置，范围：1~4 * @param Column 起始列位置，范围：1~16 * @param Number 要显示的数字，范围：0~1111 1111 1111 1111 * @param Length 要显示数字的长度，范围：1~16 * @retval 无 */ void OLED_ShowBinNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length) { uint8_t i; for (i = 0; i < Length; i++) { OLED_ShowChar(Line, Column + i, Number / OLED_Pow(2, Length - i - 1) % 2 + '0'); } } /** * @brief OLED初始化 * @param 无 * @retval 无 */ void OLED_Init(void) { uint32_t i, j; for (i = 0; i < 1000; i++) //上电延时 { for (j = 0; j < 1000; j++); } OLED_I2C_Init(); //端口初始化 OLED_WriteCommand(0xAE); //关闭显示 OLED_WriteCommand(0xD5); //设置显示时钟分频比/振荡器频率 OLED_WriteCommand(0x80); OLED_WriteCommand(0xA8); //设置多路复用率 OLED_WriteCommand(0x3F); OLED_WriteCommand(0xD3); //设置显示偏移 OLED_WriteCommand(0x00); OLED_WriteCommand(0x40); //设置显示开始行 OLED_WriteCommand(0xA1); //设置左右方向，0xA1正常 0xA0左右反置 OLED_WriteCommand(0xC8); //设置上下方向，0xC8正常 0xC0上下反置 OLED_WriteCommand(0xDA); //设置COM引脚硬件配置 OLED_WriteCommand(0x12); OLED_WriteCommand(0x81); //设置对比度控制 OLED_WriteCommand(0xCF); OLED_WriteCommand(0xD9); //设置预充电周期 OLED_WriteCommand(0xF1); OLED_WriteCommand(0xDB); //设置VCOMH取消选择级别 OLED_WriteCommand(0x30); OLED_WriteCommand(0xA4); //设置整个显示打开/关闭 OLED_WriteCommand(0xA6); //设置正常/倒转显示 OLED_WriteCommand(0x8D); //设置充电泵 OLED_WriteCommand(0x14); OLED_WriteCommand(0xAF); //开启显示 OLED_Clear(); //OLED清屏 }第四步把这些程序给我放在gpio.h或main.h里面你刚才放在xxx.c现在就要给我放在xxx.h好吧新手必须听话
#define OLED_SCL_Clr() HAL_GPIO_WritePin(GPIOA, GPIO_PIN_9, GPIO_PIN_RESET) #define OLED_SCL_Set() HAL_GPIO_WritePin(GPIOA, GPIO_PIN_9, GPIO_PIN_SET) #define OLED_SDA_Clr() HAL_GPIO_WritePin(GPIOA, GPIO_PIN_8, GPIO_PIN_RESET) #define OLED_SDA_Set() HAL_GPIO_WritePin(GPIOA, GPIO_PIN_8, GPIO_PIN_SET) // 函数声明 void OLED_Init(void); void OLED_Clear(void); void OLED_ShowChar(uint8_t Line, uint8_t Column, char Char); void OLED_ShowString(uint8_t Line, uint8_t Column, char *String); void OLED_ShowNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length); void OLED_ShowSignedNum(uint8_t Line, uint8_t Column, int32_t Number, uint8_t Length); void OLED_ShowHexNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length); void OLED_ShowBinNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length); /*OLED字模库，宽8像素，高16像素*/ static const uint8_t OLED_F8x16[][16]= { 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,// 0 0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! 1 0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 2 0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00, 0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# 3 0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00, 0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ 4 0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00, 0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% 5 0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00, 0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& 6 0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 7 0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00, 0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( 8 0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00, 0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) 9 0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00, 0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* 10 0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00, 0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ 11 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, 12 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- 13 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. 14 0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04, 0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// 15 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00, 0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 16 0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00, 0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 17 0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00, 0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 18 0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00, 0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 19 0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00, 0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 20 0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00, 0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 21 0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00, 0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 22 0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00, 0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 23 0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00, 0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 24 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00, 0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 25 0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00, 0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: 26 0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00, 0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; 27 0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00, 0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< 28 0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00, 0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= 29 0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00, 0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> 30 0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00, 0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? 31 0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00, 0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@ 32 0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00, 0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A 33 0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00, 0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B 34 0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00, 0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C 35 0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00, 0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D 36 0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00, 0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E 37 0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00, 0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F 38 0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00, 0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G 39 0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08, 0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H 40 0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00, 0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I 41 0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00, 0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J 42 0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00, 0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K 43 0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00, 0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L 44 0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00, 0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M 45 0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08, 0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N 46 0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00, 0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O 47 0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00, 0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P 48 0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00, 0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q 49 0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00, 0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R 50 0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00, 0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S 51 0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00, 0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T 52 0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08, 0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U 53 0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08, 0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V 54 0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00, 0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W 55 0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08, 0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X 56 0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00, 0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y 57 0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00, 0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z 58 0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00, 0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ 59 0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\ 60 0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00, 0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] 61 0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 62 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ 63 0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 64 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00, 0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a 65 0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00, 0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b 66 0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00, 0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c 67 0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00, 0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d 68 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00, 0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e 69 0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18, 0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f 70 0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00, 0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g 71 0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00, 0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h 72 0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00, 0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i 73 0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00, 0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j 74 0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00, 0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k 75 0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00, 0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l 76 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00, 0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m 77 0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00, 0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n 78 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00, 0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o 79 0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00, 0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p 80 0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00, 0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q 81 0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00, 0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r 82 0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00, 0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s 83 0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00, 0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t 84 0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00, 0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u 85 0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80, 0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v 86 0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80, 0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w 87 0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00, 0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x 88 0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80, 0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y 89 0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00, 0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z 90 0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02, 0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ 91 0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//| 92 0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00, 0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} 93 0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94 };第五步 回到你的main.c
第六步 给你说说我用的这两个函数
OLED_ShowString(2, 1, "Temp: "); OLED_ShowNum(2, 7, a_temp, 2);这两个函数放在循环里稍晚程序就可以工作了， OLED_ShowString(2, 1, "Temp: ");这个第一个形参（注意括号里的a，b这个ab叫形参别被别人笑话赶明，我被别人笑话过）填第几行，第二个填第几列，第三个填你要显示什么。我写的这句就是在第二行第一列写Temp:
OLED_ShowNum(2, 7, a_temp, 2);这句第一个形参也是第几行，第二个也是第几列，第三个就是你要显示什么变量，第四个就是这个变量给他多大长度。我写的这句就是在第二行第七列把温度这个变量实时显示出来这个变量我给他两位的空间。
OK 不出意外你的OLED 屏幕烧完程序应该可以显示了。
我是一个不废话又不太懂废话的博主不定期更新一些自己用过的小模块，还可能会发一些关于无人机的操作哦~
------------如有侵权请提出---------------必改正----------
